| | | |
| | | |
| Ref. | Dimension | Location | | Ref. | Dimension | Location |
| A | 50-15/16" | Center of outboard retainer screw of no. 1 mount (radiator cradle) located approximately 5" rearward of front of frame to center of outboard retainer screw on opposite side of body. NOTE: Removal of anchor nut, large washer and lower rubber pad may be required to gain access to center of retainer screw. | | a | 15” | Center of outboard retainer screw of no.1 mount (radiator cradle) located approximately 5" rearward of front of frame. NOTE: Removal of anchor nut, large washer and lower rubber pad may be required to gain access to center of retainer screw. |
| B | 38-1/4”
| Center of outboard retainer screw of no. 1 mount (radiator cradle) and center of master gage hole adjacent to no. 2 body mount on same side of body.
| | b | 9-3/4”
| Center of 5/8" master gage hole adjacent to no. 2 body mount. |
| C | 61-1/8”
| Center of outboard retainer screw of no. 1 mount (radiator cradle) and center of 5/8” master gage hole adjacent to no. 2 body mount on opposite side of body. | | c | 4”
| Center of rearmost retainer screw at no. 3 body mount (Fig. 3-12). |
| D | 44-9/16”
| Between centers of 5/8” master gage holes adjacent to no. 2 body mount across body. | | d | 4-5/16”
| Center of 5/8” master gage hole in compartment pan side rail adjacent to spring front support.
|
| E | 71-3/4”
| Center of 5/8” master gage hole adjacent to no. 2 body mount and center of 5/8” master gage hole in compartment pan side rail on same side of body adjacent to spring front support.
| | e | 15-3/4”
| Lower surface of compartment pan side rail at kick-up rear of rear axle housing (30-1/2” forward of center of hole “f”).
|
| F | 69-3/4”
| Center of outboard retainer screw of no. 1 mount (radiator cradle) and center of rearmost retainer screw at no. 3 body mount on same side of body (Fig. 3.12).
| | f | 11-1/2”
| Center of 3/4” hole in compartment pan side rail approximately 10” rearward of center of rear shackle attaching bolt to frame.
|
| G | 34-1/4”
| Between centers of rearmost retainer srews at no. 3 body mounts across body (Fig. 3-12).
| | g | 11-1/16”
| Bottom surface of dash brace adjacent to no. 2 body mount (on body).
|
| H | 81-1/2” | Center of 5/8" master gage hole adjacent to no. 2 body mount and center 5/8" master gage hole in compartment pan side rail on opposite side of body adjacent to spring support. | | h | 4-4/16”
| Bottom surface of body floor pan side rail at rear edge of stub frame (on body).
|
| I | 33-5/16”
| Between centers of 5/8” master gage holes in compartment pan side rails across body adjacent to spring front supports. | | | | |
| J | 75-3/4”
| Center of 5/8” master gage hole in compartment pan side rail adjacent to spring front support to center of 3/4” gage hole in compartment pan side rail on opposite side of body approximately 10” rearward of rear shackle attaching bolt to frame.
NOTE: Adjust pointer and lever bar if required.
| | | | |
| K | 64-13/16”
| Center of 5/8” master gage hole in compartment pan side rail adjacent to spring front support and center of 3/4” hole in compartment pan side rail on same side of body approximately 10” rearward of rear shackle attaching bolt to frame.
| | | | |
| L | 45-1/4”
| Between center (front or rear edge) of 3/4” holes in compartment pan side rails approximately 10” rearward of center of rear shackle attaching bolt to frame.
| | | | |
Frame diagram 
